Notice
Download
2018.07.05 18:45

Machinery Directive

Views 326781 Votes 0 Comment 0
?

Shortcut

PrevPrev Article

NextNext Article

Larger Font Smaller Font Up Down Go comment Print
?

Shortcut

PrevPrev Article

NextNext Article

Larger Font Smaller Font Up Down Go comment Print

1.  기계안전지침(2006/42/EC)의 구성.

서 론 : 작성에 해당되는 지침과 전반적인 해설 및 유의사항
본 문 : 지침을 적용하기 위한 조문, 가맹국에 대한 법적 의무나 권한
Annex I : 설계 및 제조에 관한 건강과 안전의 필수 요구사항
Annex II : 적합성 선언서에 관한 사항
Annex III : CE – Marking에 관한 사항
Annex IV : Notified Body로부터 EU 형식시험을 받아야 하는 기계류 목록
Annex V : 적합성 선언 및 기술파일
Annex VI : EU 형식시험
Annex VII : Notified Body 기준

 


2.  대상기기

A) 기계의 정의

전기, 공기압 및 유압, 무게 등을 에너지원으로 하여 적어도 1개 이상의 작동부분이 있는 제품

B) 안전부품의 정의

건강이나 안전에 관여하는 기계류의 부품으로, 단독으로 출하되는 기기

 


3.  기계지침의 대상제품 외의 기기

다른 기술지침에 의해 인증 관리되는 것으로써 다음과 같습니다.

A) 사람의 힘을 동력원으로 사용하는 기계류
B) 환자에 직접 접촉되는 의료기기
C) 유원지에서 사용하는 오락용 특수 기기
D) 원자력 관련기기
E) 농업 및 임업용 트랙터
F) 기계 일부를 구성하는 방사원
G) 스팀 보일러, 탱크 및 압력용기
H) 소화기 및 시스템
I) 인간을 운반하는 공중 케이블을 포함한 케이블카
J) 군용, 경찰용인 특수구조의 기기
K) 석유, 중유, 등의 저장 탱크나 파이프라인
L) 승객을 공중, 도로, 선로, 수중에서 운반하는 전용 차량이나, 트레일러 및 화물을 공중, 도로, 선로, 수상으로 운반하는 수단에 이용하는 장비 (광물 채취 산업에서 것에 관해서는 제외)
M) 해상 항해용 선박 및 관련 장치
N) 빌딩, 건축물에 고정된 리프트로, 수평에서 15도 이상으로 고정된 가이드 사이를 움직이는 차량을 이용하여 사람이나 화물을 운반하는 것
O) 록/피니언을 이용하여 사람을 운반하는 차량
P) 극장용 엘리베이터
Q) 건설 현장용 리프트
R) 광산용 윈치

요약하면 기계, 기기로서 “가동부”를 가지고, 그것이 인체 등에 위해를 줄 가능성이 있는 것이면, 기계류지침의 대상이 됩니다. 공업용뿐 만 아니라, 가정용이나 상업용의 기계류도 포함됩니다.

뿐만 아니라 기계류의 위험성이 주로 전기적인 경우는, 저전압 지침에 따라 추가적인 인증이 요구되어지고 나아가 전자파 지침 등도 함께 인증되어야 할 경우가 있습니다. 단, 전자파 지침의 경우, 예외적으로 고정장치로 사용되는 특수한 경우는 현장에서 설치된 모든 대상장비, 설비에 대해 일괄적으로 EMC시험을 수행하고 인증할 수 있어 개별적 시험을 하지 않는 경우도 있습니다.

전시회나 샘플용 기계류, 안전 부품이라면, “기계류의 지침에 불일치” ” 비판매용”,” 전시회용”, “전시 샘플”등의 문구를 부착하여 기계안전 인증을 받지 않을 수 있습니다.

 


4.  기계지침의 규격구분

기계 안전에 관한 유럽 통일 규격은 A규격, B 규격, C 규격의 3종류로부터 구성되어 있습니다. 물론 기술문서 (Technical Construction File : TCF)는 3종류의 모든 규격을 충족해야 합니다.

A) A 규격( 기본적 안전 규격)

모든 기계에 대한 기본적 안전규격으로써 기본 개념, 설계 원칙 및 일반적 측면을 규정하는 규격.

B) B 규격( 그룹 안전 규격)

기계의 용도 및 목적에 따라 광범위하게 구분된 기계 등에 적용되는 안전에 관계되는 측면, 또는 안전관련장치의 하나의 형식을 취급하는 규격

a) B1규격은 특정 안전성 측면에 관한 규격으로, 예를 들면 안전거리, 표면온도, 소음 등에 관한 것

b) B2규격은 안전관련 장치 및 기계부품 등에 관한 규격으로, 예를 들면 인터록 장치, 감압장치, 방호장치 등에 관한 내용이 기술되어 있습니다.

C) C 규격(기계에 관한 안전 규격)

특정 기계 또는 기계 그룹에 관한 상세한 안전 요구사항을 규정하는 규격

a) 예를 들면, 자동선반, 회전톱 등에 관한 세부 규격입니다.

 


5.  기계류지침의 Annex IV 고 위험군의 기계류

이들 기계류는 고 위험군기계류로써 유럽위원회로부터 권한을 부여 받은 Notified Body(NB)에 의해 해당되는 제품별 규격에 따라 ” EU형식시험”, 등 기계류지침 절차에 따라 인증되고 지속적 적합성을 관리 합니다.

일반적으로 원형 톱 기계, 밴드 톱 기계, 사출, 압출용 플라스틱 가공 기계, 자동차용 lift기계 및 기타 안전 기능 품목과 전도, 낙하물 보호장치가 필요한 기계류 등으로써 인체에게 심각한 손상을 가할 수 있는 기계류 입니다.

1. Circular saws (single- or multi-blade) for working with wood and material with similar physical characteristics or for working with meat and material with similar physical characteristics, of the following types:

1.1. sawing machinery with fixed blade(s) during cutting, having a fixed bed or support with manual feed of the workpiece or with a demountable power feed;

1.2. sawing machinery with fixed blade(s) during cutting, having a manually operated reciprocating saw-bench or carriage;

1.3 sawing machinery with fixed blade(s) during cutting, having a built-in mechanical feed device for the workpieces, with manual loading and/or unloading;

1.4. sawing machinery with movable blade(s) during cutting, having mechanical movement of the blade, with manual loading and/or unloading.

2. Hand-fed surface planing machinery for woodworking.

3. Thicknessers for one-side dressing having a built-in mechanical feed device, with manual loading and/or unloading for woodworking.

4. Band-saws with manual loading and/or unloading for working with wood and material with similar physical characteristics or for working with meat and material with similar physical characteristics, of the following types:

4.1. sawing machinery with fixed blade(s) during cutting, having a fixed or reciprocating-movement bed or support for the workpiece;

4.2. sawing machinery with blade(s) assembled on a carriage with reciprocating motion.

5. Combined machinery of the types referred to in points 1 to 4 and in point 7 for working with wood and material with similar physical characteristics.

6. Hand-fed tenoning machinery with several tool holders for woodworking.

7. Hand-fed vertical spindle moulding machinery for working with wood and material with similar physical characteristics.

8. Portable chainsaws for woodworking.

9. Presses, including press-brakes, for the cold working of metals, with manual loading and/or unloading, whose movable working parts may have a travel exceeding 6 mm and a speed exceeding 30 mm/s.

10. Injection or compression plastics-moulding machinery with manual loading or unloading.

11. Injection or compression rubber-moulding machinery with manual loading or unloading.

12. Machinery for underground working of the following types:

12.1. locomotives and brake-vans;

12.2. hydraulic-powered roof supports.

13. Manually loaded trucks for the collection of household refuse incorporating a compression mechanism.

14. Removable mechanical transmission devices including their guards.

15. Guards for removable mechanical transmission devices.

16. Vehicle servicing lifts.

17. Devices for the lifting of persons or of persons and goods involving a hazard of falling from a vertical height of more than three metres.

18. Portable cartridge-operated fixing and other impact machinery.

19. Protective devices designed to detect the presence of persons.

20. Power-operated interlocking movable guards designed to be used as safeguards in machinery referred to in points 9, 10 and 11.

21. Logic units to ensure safety functions.

22. Roll-over protective structures (ROPS).

23. Falling-object protective structures (FOPS).

 


6.  TCF (Technical Construction Files)에 포함할 정보

A) 자기 적합성 선언서
B) 위험분석 보고서(Risk Analysis Report)
C) 사용 설명서
D) 도면 류 (회로도, 기구도 등)
E) 설계계산서
F) 제조자가 수행한 시험결과 등에 관한 성적서 및 보고서
G) 취급, 설치 또는 운전 설명서
H) 유지보수에 관한 사항
I) 사용된 부품 목록 및 부품에 관한 인증서

참조 :

a) 유럽 CE-Marking은 제조자, 자기 적합성 선언을 하는 자의 책임을 강조하고 있습니다. 따라서 설계, 개발, 제조, 시험 등 제품의 안전에 관련된 모든 사항을 제조자 또는 자기 적합성 선언을 하는 자의 책임으로 인식하고 있습니다.

b) CE-Marking은 제조자의 관리하에서 수행된 시험성적서 등 모든 적합성 확인결과를 우선적으로 신뢰합니다. 일부 제조자의 여건으로 스스로 시험을 수행할 수 없는 경우, 제3의 공인시험기관의 성적서 등을 채택하기도 하지만 근본적으로 제품의 안전에 대한 모든 책임은 제조자에 국한 합니다. 유럽위원회에서 인증권한을 부여 받은 승인기관 (Notified Body : NB)(Notified Body)은 ILAC(International Laboratory Accreditation Committee)산하 APLAC 등으로부터 인정 받은 시험기관의 성적서를 인정하고 있으며 필요에 따라 이들 시험기관 지정서 또는 적용된 시험 절차서와 사용된 계측기기의 교정여부를 재 확인하기도 합니다.

 


7.  인증절차

다음과 같이 4가지의 방식이 있습니다.

A) Annex 4에 기술된 고 위험군 기계류

승인기관 (Notified Body : NB)을 통한 인증취득

B) Annex 4가 아닌 일반 기계류 (Annex Ⅱ A)

자기 적합성 선언(완성품에 대한 적합성의 입증으로써 CE 마크를 부착)으로 취득

C) 기계 부품류에 관한 자기 적합성 선언(Annex Ⅱ B)

자기 적합성 선언(완성품에 대한 적합성의 입증으로써 CE 마크를 부착)으로 취득

D) 안전 부품류에 관한 자기 적합성 선언 (Annex Ⅱ C)

자기 적합성 선언(완성품에 대한 적합성의 입증으로써 CE 마크를 부착)으로 취득

참고 : ②와③의 경우, 자기 적합성 선언서를 작성하고 관련 기술문서를 보관 함으로써 규격에 적합함을 선언할 수 있지만 해당제품이나 포장 등에 CE 마크를 부착 할 수 없습니다.

 


8.   적용 대상 EN 규격

EN 1005-1:2001+A1:2008-Safety of machinery – Human physical performance – Part 1: Terms and definitions
EN 1005-2:2003+A1:2008-Safety of machinery – Human physical performance – Part 2: Manual handling of machinery and component parts of machinery
EN 1005-3:2002+A1:2008-Safety of machinery – Human physical performance – Part 3: Recommended force limits for machinery operation
EN 1005-4:2005+A1:2008-Safety of machinery – Human physical performance – Part 4: Evaluation of working postures and movements in relation to machinery
EN 1010-1:2004+A1:2010-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 1: Common requirements
EN 1010-2:2006+A1:2010-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 2: Printing and varnishing machines including pre-press machinery
EN 1010-3:2002+A1:2009-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 3: Cutting machines
EN 1010-4:2004+A1:2009-Safety of machinery – Safety requirements for the design and construction of printing and paper converting machines – Part 4: Bookbinding, paper converting and finishing machines
EN 1012-1:2010-Compressors and vacuum pumps – Safety requirements – Part 1: Air compressors
EN 1012-2:1996+A1:2009-Compressors and vacuum pumps – Safety requirements – Part 2: Vacuum pumps
EN 1028-1:2002+A1:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 1: Classification – General and safety requirements
EN 1028-2:2002+A1:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps with primer – Part 2: Verification of general and safety requirements
EN 1032:2003+A1:2008-Mechanical vibration – Testing of mobile machinery in order to determine the vibration emission value
EN 1034-1:2000+A1:2010-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 1: Common requirements
EN 1034-13:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 13: Machines for de-wiring bales and units
EN 1034-14:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 14: Reel splitter
EN 1034-16:2012 (new)-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 16: Paper and board making machines
EN 1034-2:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 2: Barking drums
EN 1034-22:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 22: Wood Grinders
EN 1034-3:2011-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 3: Rereelers and winders
EN 1034-4:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 4: Pulpers and their loading facilities
EN 1034-5:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 5: Sheeters
EN 1034-6:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 6: Calender
EN 1034-7:2005+A1:2009-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 7: Chests
EN 1034-8:2012 (new)-Safety of machinery – Safety requirements for the design and construction of paper making and finishing machines – Part 8: Refining plants
EN 1037:1995+A1:2008-Safety of machinery – Prevention of unexpected start-up
EN 1088:1995+A2:2008-Safety of machinery – Interlocking devices associated with guards – Principles for design and selection
EN 1093-1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 1: Selection of test methods
EN 1093-11:2001+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 11: Decontamination index
EN 1093-2:2006+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 2: Tracer gas method for the measurement of the emission rate of a given pollutant
EN 1093-3:2006+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 3: Test bench method for the measurement of the emission rate of a given pollutant
EN 1093-4:1996+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 4: Capture efficiency of an exhaust system – Tracer method
EN 1093-6:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 6: Separation efficiency by mass, unducted outlet
EN 1093-7:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 7: Separation efficiency by mass, ducted outlet
EN 1093-8:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 8: Pollutant concentration parameter, test bench method
EN 1093-9:1998+A1:2008-Safety of machinery – Evaluation of the emission of airborne hazardous substances – Part 9: Pollutant concentration parameter, room method
EN 1114-1:2011-Plastics and rubber machines – Extruders and extrusion lines – Part 1: Safety requirements for extruders
EN 1114-3:2001+A1:2008-Plastics and rubber machines – Extruders and extrusion lines – Part 3: Safety requirements for haul-offs
EN 1127-1:2011-Explosive atmospheres – Explosion prevention and protection – Part 1: Basic concepts and methodology
EN 1127-2:2002+A1:2008-Explosive atmospheres – Explosion prevention and protection – Part 2: Basic concepts and methodology for mining
EN 115-1:2008+A1:2010-Safety of escalators and moving walks – Part 1: Construction and installation
EN 1175-1:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 1: General requirements for battery powered trucks
EN 1175-2:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 2: General requirements of internal combustion engine powered trucks
EN 1175-3:1998+A1:2010-Safety of industrial trucks – Electrical requirements – Part 3: Specific requirements for the electric power transmission systems of internal combustion engine powered trucks
EN 12001:2003+A1:2009-Conveying, spraying and placing machines for concrete and mortar – Safety requirements
EN 12012-1:2007+A1:2008-Plastics and rubber machines – Size reduction machines – Part 1: Safety requirements for blade granulators
EN 12012-3:2001+A1:2008-Plastics and rubber machines – Size reduction machines – Part 3: Safety requirements for shredders
EN 12012-4:2006+A1:2008-Plastics and rubber machines – Size reduction machines – Part 4: Safety requirements for agglomerators
EN 12013:2000+A1:2008-Plastics and rubber machines – Internal mixers – Safety requirements
EN 12016:2004+A1:2008-Electromagnetic compatibility – Product family standard for lifts, escalators and moving walks – Immunity
EN 12041:2000+A1:2009-Food processing machinery – Moulders – Safety and hygiene requirements
EN 12042:2005+A1:2010-Food processing machinery – Automatic dividers – Safety and hygiene requirements
EN 12043:2000+A1:2010-Food processing machinery – Intermediate provers – Safety and hygiene requirements
EN 12044:2005+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Cutting and punching machines – Safety requirements
EN 12053:2001+A1:2008-Safety of industrial trucks – Test methods for measuring noise emissions
EN 12077-2:1998+A1:2008-Cranes safety – Requirements for health and safety – Part 2: Limiting and indicating devices
EN 12110:2002+A1:2008-Tunnelling machines – Air locks – Safety requirements
EN 12111:2002+A1:2009-Tunnelling machines – Road headers, continuous miners and impact rippers – Safety requirements
EN 12158-1:2000+A1:2010-Builders’ hoists for goods – Part 1: Hoists with accessible platforms
EN 12158-2:2000+A1:2010-Builders’ hoists for goods – Part 2: Inclined hoists with non-accessible load carrying devices
EN 12159:2000+A1:2009-Builders hoists for persons and materials with vertically guided cages
EN 12162:2001+A1:2009-Liquid pumps – Safety requirements – Procedure for hydrostatic testing
EN 1218-1:1999+A1:2009-Safety of woodworking machines – Tenoning machines – Part 1: Single end tenoning machines with sliding table
EN 1218-2:2004+A1:2009-Safety of woodworking machines – Tenoning machines – Part 2: Double end tenoning and/or profiling machines fed by chain or chains
EN 1218-3:2001+A1:2009-Safety of woodworking machines – Tenoning machines – Part 3: Hand fed tenoning machines with sliding table for cutting structural timbers
EN 1218-4:2004+A2:2009-Safety of woodworking machines – Tenoning machines – Part 4: Edge banding machines fed by chain(s)
EN 1218-5:2004+A1:2009-Safety of woodworking machines – Tenoning machines – Part 5: one side profiling machines with fixed table and feed rollers or feed chain
EN 12198-1:2000+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 1: General principles
EN 12198-2:2002+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 2: Radiation emission measurement procedure
EN 12198-3:2002+A1:2008-Safety of machinery – Assessment and reduction of risks arising from radiation emitted by machinery – Part 3: Reduction of radiation by attenuation or screening
EN 12203:2003+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Shoe and leather presses – Safety requirements
EN 12254:2010-Screens for laser working places – Safety requirements and testing
EN 12267:2003+A1:2010-Food processing machinery – Circular saw machines – Safety and hygiene requirements
EN 12268:2003+A1:2010-Food processing machinery – Band saw machines – Safety and hygiene requirements
EN 12301:2000+A1:2008-Plastics and rubber machines – Calenders – Safety requirements
EN 12312-1:2001+A1:2009-Aircraft ground support equipment – Specific requirements – Part 1: Passenger stairs
EN 12312-10:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 10: Container/Pallet transfer transporters
EN 12312-12:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 12: Potable water service equipment
EN 12312-13:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 13: Lavatory service equipment
EN 12312-14:2006+A1:2009-Aircraft ground support equipment – Specific requirements – Part 14: Disabled/incapacitated passenger boarding vehicles
EN 12312-15:2006+A1:2009-Aircraft ground support equipment – Specific requirements – Part 15: Baggage and equipment tractors
EN 12312-16:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 16: Air start equipment
EN 12312-17:2004+A1:2009-Aircraft ground support equipment – Specific requirements – Part 17: Air conditioning equipment
EN 12312-18:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 18: Nitrogen or Oxygen units
EN 12312-19:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 19: Aircraft jacks, axle jacks and hydraulic tail stanchions
EN 12312-2:2002+A1:2009-Aircraft ground support equipment – Specific requirements – Part 2: Catering vehicles
EN 12312-20:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 20: Electrical ground power units
EN 12312-3:2003+A1:2009-Aircraft ground support equipment – Specific requirements – Part 3: Conveyor belt vehicles
EN 12312-4:2003+A1:2009-Aircraft ground support equipment – Specific requirements – Part 4: Passenger boarding bridges
EN 12312-5:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 5: Aircraft fuelling equipment
EN 12312-6:2004+A1:2009-Aircraft ground support equipment – Specific requirements – Part 6: Deicers and deicing/antiicing equipment
EN 12312-7:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 7: Air-craft movement equipment
EN 12312-8:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 8: Maintenance stairs and platforms
EN 12312-9:2005+A1:2009-Aircraft ground support equipment – Specific requirements – Part 9: Container/Pallet loaders
EN 12321:2003+A1:2009-Underground mining machinery – Specification for the safety requirements of armoured face conveyors
EN 12331:2003+A2:2010-Food processing machinery – Mincing machines – Safety and hygiene requirements
EN 12336:2005+A1:2008-Tunnelling machines – Shield machines, thrust boring machines, auger boring machines, lining erection equipment – Safety requirements
EN 12348:2000+A1:2009-Core drilling machines on stand – Safety
EN 12355:2003+A1:2010-Food processing machinery – Derinding-, skinning- and membrane removal machines – Safety and hygiene requirements
EN 12385-1:2002+A1:2008-Steel wire ropes – Safety – Part 1: General requirements
EN 12385-10:2003+A1:2008-Steel wire ropes – Safety – Part 10: Spiral ropes for general structural applications
EN 12385-2:2002+A1:2008-Steel wire ropes – Safety – Part 2: Definitions, designation and classification
EN 12385-3:2004+A1:2008-Steel wire ropes – Safety – Part 3: Information for use and maintenance
EN 12385-4:2002+A1:2008-Steel wire ropes – Safety – Part 4: Stranded ropes for general lifting applications
EN 12387:2005+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Modular shoe repair equipment – Safety requirements
EN 12409:2008+A1:2011-Plastics and rubber machines – Thermoforming machines – Safety requirements
EN 12417:2001+A2:2009-Machine tools – Safety – Machining centres
EN 12418:2000+A1:2009-Masonry and stone cutting-off machines for job site – Safety
EN 12463:2004+A1:2011-Food processing machinery – Filling machines and auxiliary machines – Safety and hygiene requirements
EN 1247:2004+A1:2010-Foundry machinery – Safety requirements for ladles, pouring equipment, centrifugal casting machines, continuous and semi continuous casting machines
EN 1248:2001+A1:2009-Foundry machinery – Safety requirements for abrasive blasting equipment
EN 12505:2000+A1:2009-Food processing machinery – Centrifugal machines for processing edible oils and fats – Safety and hygiene requirements
EN 12525:2000+A2:2010-Agricultural machinery – Front loaders – Safety
EN 12545:2000+A1:2009-Footwear, leather and imitation leather goods manufacturing machines – Noise test code – Common requirements
EN 12547:1999+A1:2009-Centrifuges – Common safety requirements
EN 12549:1999+A1:2008-Acoustics – Noise test code for fastener driving tools – Engineering method
EN 12581:2005+A1:2010-Coating plants – Machinery for dip coating and electrodeposition of organic liquid coating material – Safety requirements
EN 12601:2010-Reciprocating internal combustion engine driven generating sets – Safety
EN 12621:2006+A1:2010-Machinery for the supply and circulation of coating materials under pressure – Safety requirements
EN 12622:2009-Safety of machine tools – Hydraulic press brakes
EN 12629-1:2000+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 1: Common requirements
EN 12629-2:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 2: Block making machines
EN 12629-3:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 3: Slide and turntable machines
EN 12629-4:2001+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 4:Concrete roof tile making machines
EN 12629-5-1:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-1: Pipe making machines manufacturing in the vertical axis
EN 12629-5-2:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-2: Pipe making machines manufacturing in the horizontal axis
EN 12629-5-3:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-3: Pipe prestressing machines
EN 12629-5-4:2003+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 5-4: Concrete pipe coating machines
EN 12629-6:2004+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 6: Stationary and mobile equipment for the manufacture of precast reinforced products
EN 12629-7:2004+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 7: Stationary and mobile equipment for long line manufacture of prestressed products
EN 12629-8:2002+A1:2010-Machines for the manufacture of constructional products from concrete and calcium-silicate – Safety – Part 8: Machines and equipment for the manufacture of constructional products from calcium-silicate (and concrete)
EN 12635:2002+A1:2008-Industrial, commercial and garage doors and gates – Installation and use
EN 12643:1997+A1:2008-Earth-moving machinery – Rubber-tyred machines – Steering requirements (ISO 5010:1992 modified)
EN 12644-1:2001+A1:2008-Cranes – Information for use and testing – Part 1: Instructions
EN 12644-2:2000+A1:2008-Cranes – Information for use and testing – Part 2: Marking
EN 12649:2008+A1:2011-Concrete compactors and smoothing machines – Safety
EN 1265:1999+A1:2008-Safety of machinery – Noise test code for foundry machines and equipment
EN 12653:1999+A2:2009-Footwear, leather and imitation leather manufacturing machines – Nailing machines – Safety requirements
EN 12693:2008-Refrigerating systems and heat pumps – Safety and environmental requirements – Positive displacement refrigerant compressors
EN 12717:2001+A1:2009-Safety of machine tools – Drilling machines
EN 12733:2001+A1:2009-Agricultural and forestry machinery – Pedestrian controlled motor mowers – Safety
EN 12750:2001+A1:2009-Safety of woodworking machines – Four-sided moulding machines
EN 12753:2005+A1:2010-Thermal cleaning systems for exhaust gas from surface treatment equipment – Safety requirements
EN 12757-1:2005+A1:2010-Mixing machinery for coating materials – Safety requirements – Part 1: Mixing machinery for use in vehicle refinishing
EN 12779:2004+A1:2009-Safety of woodworking machines – Chip and dust extraction systems with fixed installation – Safety related performances and safety requirements
EN 12851:2005+A1:2010-Food processing machinery – Catering attachments for machines having an auxiliary drive hub – Safety and hygiene requirements
EN 12852:2001+A1:2010-Food processing machinery – Food processors and blenders – Safety and hygiene requirements
EN 12853:2001+A1:2010-Food processing machinery – Hand-held blenders and whisks – Safety and hygiene requirements
EN 12854:2003+A1:2010-Food processing machinery – Beam mixers – Safety and hygiene requirements
EN 12855:2003+A1:2010-Food processing machinery – Rotating bowl cutters – Safety and hygiene requirements
EN 12881-1:2005+A1:2008-Conveyor belts – Fire simulation flammability testing – Part 1: Propane burner tests
EN 12881-2:2005+A1:2008-Conveyor belts – Fire simulation flammability testing – Part 2: Large scale fire test
EN 12882:2008-Conveyor belts for general purpose use – Electrical and flammability safety requirements
EN 12921-1:2005+A1:2010-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 1: Common safety requirements
EN 12921-2:2005+A1:2008-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 2: Safety of machines using water based cleaning liquids
EN 12921-3:2005+A1:2008-Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours – Part 3: Safety of machines using flammable cleaning liquids
EN 12921-4:2005+A1:2008-Machines for surface cleaning and pretreatment of industrial items using liquids and vapours – Part 4: Safety of machines using halogenated solvents
EN 12957:2001+A1:2009-Machine tools – Safety – Electro discharge machines
EN 12965:2003+A2:2009-Tractors and machinery for agriculture and forestry – Power take-off (PTO) drive shafts and their guards – Safety
EN 12978:2003+A1:2009-Industrial, commercial and garage doors and gates – Safety devices for power operated doors and gates – Requirements and test methods
EN 12981:2005+A1:2009-Coating plants – Spray booths for application of organic powder coating material – Safety requirements
EN 12984:2005+A1:2010-Food processing machinery – Portable and/or hand-guided machines and appliances with mechanically driven cutting tools – Safety and hygiene requirements
EN 1299:1997+A1:2008-Mechanical vibration and shock – Vibration isolation of machines – Information for the application of source isolation
EN 12999:2011-Cranes – Loader cranes
EN 13000:2010-Cranes – Mobile cranes
EN 13001-1:2004+A1:2009-Cranes – General design – Part 1: General principles and requirements
EN 13001-2:2011/AC:2012 (new)-EN 13001-3-1:2012 (new)
EN 13001-2:2011-Crane safety – General design – Part 2: Load actions
EN 13001-3-1:2012 (new)-Cranes – General Design – Part 3-1: Limit States and proof competence of steel structure
EN 13015:2001+A1:2008-Maintenance for lifts and escalators – Rules for maintenance instructions
EN 13019:2001+A1:2008-Machines for road surface cleaning – Safety requirements
EN 13020:2004+A1:2010-Road surface treatment machines – Safety requirements
EN 13021:2003+A1:2008-Winter service machines – Safety requirements
EN 13023:2003+A1:2010-Noise measurement methods for printing, paper converting, paper making machines and auxiliary equipment – Accuracy grades 2 and 3
EN 13035-1:2008-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 1: Storage, handling and transportation equipment inside the factory
EN 13035-11:2006+A1:2010-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 11: Drilling machines
EN 13035-2:2008-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 2: Storage, handling and transportation equipment outside the factory
EN 13035-3:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 3: Cutting machines
EN 13035-4:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 4: Tilting tables
EN 13035-5:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 5: Machines and installations for stacking and de-stacking
EN 13035-6:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 6: Machines for break-out
EN 13035-7:2006+A1:2009-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 7: Cutting machines for laminated glass
EN 13035-9:2006+A1:2010-Machines and plants for the manufacture, treatment and processing of flat glass – Safety requirements – Part 9: Washing installations
EN 13042-1:2007+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 1: Gob feeder
EN 13042-2:2004+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 2: Handling machines for feeding
EN 13042-3:2007+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 3: IS machines
EN 13042-5:2003+A1:2009-Machines and plants for the manufacture, treatment and processing of hollow glass – Safety requirements – Part 5: Presses
EN 13059:2002+A1:2008-Safety of industrial trucks – Test methods for measuring vibration
EN 13102:2005+A1:2008-Ceramic machines – Safety – Loading and unloading of fine clay tiles
EN 13112:2002+A1:2009-Tannery machines – Splitting and bandknife shearing machines – Safety requirements
EN 13113:2002+A1:2010-Tannery machines – Roller coating machines – Safety requirements
EN 13114:2002+A1:2009-Tannery machines – Rotating process vessels – Safety requirements
EN 13118:2000+A1:2009-Agricultural machinery – Potato harvesting equipment – Safety
EN 13120:2009-Internal blinds – Performance requirements including safety
EN 13128:2001+A2:2009-Safety of machine tools – Milling machines (including boring machines)
EN 13135-1:2003+A1:2010-Cranes – Equipment – Part 1: Electrotechnical equipment
EN 13135-2:2004+A1:2010-Cranes – Equipment – Part 2: Non-electrotechnical equipment
EN 13140:2000+A1:2009-Agricultural machinery – Sugar beet and fodder beet harvesting equipment – Safety
EN 13155:2003+A2:2009-Cranes – Safety – Non-fixed load lifting attachments
EN 13157:2004+A1:2009-Cranes – Safety – Hand powered cranes
EN 13208:2003+A1:2010-Food processing machinery – Vegetable peelers – Safety and hygiene requirements
EN 13218:2002+A1:2008-Machine tools – Safety – Stationary grinding machines
EN 13241-1:2003+A1:2011-Industrial, commercial and garage doors and gates – Product standard – Part 1: Products without fire resistance or smoke control characteristics
EN 13288:2005+A1:2009-Food processing machinery – Bowl lifting and tilting machines – Safety and hygiene requirements
EN 13355:2004+A1:2009-Coating plants – Combined booths – Safety requirements
EN 13367:2005+A1:2008-Ceramic machines – Safety – Transfer platforms and cars
EN 13389:2005+A1:2009-Food processing machinery – Mixers with horizontal shafts – Safety and hygiene requirements
EN 13390:2002+A1:2009-Food processing machinery – Pie and tart machines – Safety and hygiene requirements
EN 13411-1:2002+A1:2008-Terminations for steel wire ropes – Safety – Part 1: Thimbles for steel wire rope slings
EN 13411-2:2001+A1:2008-Terminations for steel wire ropes – Safety – Part 2: Splicing of eyes for wire rope slings
EN 13411-3:2004+A1:2008-Terminations for steel wire ropes – Safety – Part 3: Ferrules and ferrule-securing
EN 13411-4:2011-Terminations for steel wire ropes – Safety – Part 4: Metal and resin socketing
EN 13411-5:2003+A1:2008-Terminations for steel wire ropes – Safety – Part 5: U-bolt wire rope grips
EN 13411-6:2004+A1:2008-Terminations for steel wire ropes – Safety – Part 6: Asymmetric wedge socket
EN 13411-7:2006+A1:2008-Terminations for steel wire ropes – Safety – Part 7: Symmetric wedge socket
EN 13411-8:2011-Terminations for steel wire ropes – Safety – Part 8: Swage terminals and swaging
EN 13414-1:2003+A2:2008-Steel wire rope slings – Safety – Part 1: Slings for general lifting service
EN 13414-2:2003+A2:2008-Steel wire rope slings – Safety – Part 2: Specification for information for use and maintenance to be provided by the manufacturer
EN 13414-3:2003+A1:2008-Steel wire rope slings – Safety – Part 3: Grommets and cable-laid slings
EN 13418:2004+A1:2008-Plastics and rubber machines – Winding machines for film or sheet – Safety requirements
EN 13448:2001+A1:2009-Agricultural and forestry machinery – Inter-row mowing units – Safety
EN 13457:2004+A1:2010-Footwear, leather and imitation leather goods manufacturing machines – Splitting, skiving, cutting, cementing and cement drying machines – Safety requirements
EN 13478:2001+A1:2008-Safety of machinery – Fire prevention and protection
EN 13490:2001+A1:2008-Mechanical vibration – Industrial trucks – Laboratory evaluation and specification of operator seat vibration
EN 13524:2003+A1:2009-Highway maintenance machines – Safety requirements
EN 13525:2005+A2:2009-Forestry machinery – Wood chippers – Safety
EN 13531:2001+A1:2008-Earth-moving machinery – Tip-over protection structure (TOPS) for compact excavators – Laboratory tests and performance requirements (ISO 12117:1997 modified)
EN 13534:2006+A1:2010-Food processing machinery – Curing injection machines – Safety and hygiene requirements
EN 13557:2003+A2:2008-Cranes – Controls and control stations
EN 13561:2004+A1:2008-External blinds – Performance requirements including safety
EN 13570:2005+A1:2010-Food processing machinery – Mixing machines – Safety and hygiene requirements
EN 13586:2004+A1:2008-Cranes – Access
EN 13591:2005+A1:2009-Food processing machinery – Fixed deck oven loaders – Safety and hygiene requirements
EN 13617-1:2004+A1:2009-Petrol filling stations – Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
EN 13621:2004+A1:2010-Food processing machinery – Salad dryers – Safety and hygiene requirements
EN 13659:2004+A1:2008-Shutters – Performance requirements including safety
EN 13675:2004+A1:2010-Safety of machinery – Safety requirements for tube forming and rolling mills and their finishing line equipment
EN 13683:2003+A2:2011-Garden equipment – Integrally powered shredders/chippers – Safety
EN 13684:2004+A3:2009-Garden equipment – Pedestrian controlled lawn aerators and scarifiers – Safety
EN 13731:2007-Lifting bag systems for fire and rescue service use – Safety and performance requirements
EN 13732:2002+A2:2009-Food processing machinery – Bulk Milk Coolers on Farms – Requirements for construction, performance, suitability for use, safety and hygiene
EN 13736:2003+A1:2009-Safety of machine tools – Pneumatic presses
EN 1374:2000+A1:2010-Agricultural machinery – Silos stationary unloaders for round silos – Safety
EN 13862:2001+A1:2009-Floor cutting-off machines – Safety
EN 13870:2005+A1:2010-Food processing machinery – Chop cutting machines – Safety and hygiene requirements
EN 13871:2005+A1:2010-Food processing machinery – Cubes cutting machinery – Safety and hygiene requirements
EN 13885:2005+A1:2010-Food processing machinery – Clipping machines – Safety and hygiene requirements
EN 13886:2005+A1:2010-Food processing machinery – Cooking kettles equipped with powered stirrer and/or mixer – Safety and hygiene requirements
EN 13889:2003+A1:2008-Forged steel shackles for general lifting purposes – Dee shackles and bow shackles – Grade 6 – Safety
EN 13898:2003+A1:2009-Machine tools – Safety – Sawing machines for cold metal
EN 13951:2003+A1:2008-Liquid pumps – Safety requirements – Agrifoodstuffs equipment – Design rules to ensure hygiene in use
EN 13954:2005+A1:2010-Food processing machinery – Bread slicers – Safety and hygiene requirements
EN 13977:2011-Railway applications – Track – Safety requirements for portable machines and trolleys for construction and maintenance
EN 1398:2009-Dock levellers – Safety requirements
EN 13985:2003+A1:2009-Machine tools – Safety – Guillotine shears
EN 14010:2003+A1:2009-Safety of machinery – Equipment for power driven parking of motor vehicles – Safety and EMC requirements for design, manufacturing, erection and commissioning stages
EN 14017:2005+A2:2009-Agricultural and forestry machinery – Solid fertilizer distributors – Safety
EN 14018:2005+A1:2009-Agricultural and forestry machinery – Seed drills – Safety
EN 14033-3:2009+A1:2011-Railway applications – Track – Railbound construction and maintenance machines – Part 3: General safety requirements
EN 14043:2005+A1:2009-High rise aerial appliances for fire service use – Turntable ladders with combined movements – Safety and performance requirements and test methods
EN 14044:2005+A1:2009-High rise aerial appliances for fire service use – Turntable ladders with sequential movements – Safety and performance requirements and test methods
EN 14070:2003+A1:2009-Safety of machine tools – Transfer and special-purpose machines
EN 1417:1996+A1:2008-Plastics and rubber machines – Two roll mills – Safety requirements
EN 14238:2004+A1:2009-Cranes – Manually controlled load manipulating devices
EN 14439:2006+A2:2009-Cranes – Safety – Tower cranes
EN 14462:2005+A1:2009-Surface treatment equipment – Noise test code for surface treatment equipment including its ancillary handling equipment – Accuracy grades 2 and 3
EN 14466:2005+A1:2008-Fire-fighting pumps – Portable pumps – Safety and performance requirements, tests
EN 14492-1:2006+A1:2009-Cranes – Power driven winches and hoists – Part 1: Power driven winches
EN 14492-2:2006+A1:2009-Cranes – Power driven winches and hoists – Part 2: Power driven hoists
EN 14502-2:2005+A1:2008-Cranes – Equipment for the lifting of persons – Part 2: Elevating control stations
EN 1459:1998+A3:2012-Safety of industrial trucks – Self-propelled variable reach trucks
EN 14655:2005+A1:2010-Food processing machinery – Baguette slicers – Safety and hygiene requirements
EN 14656:2006+A1:2010-Safety of machinery – Safety requirements for extrusion presses for steel and non-ferrous metals
EN 14658:2005+A1:2010-Continuous handling equipment and systems – General safety requirements for continuous handling equipment for opencast lignite mining
EN 14673:2006+A1:2010-Safety of machinery – Safety requirements for hydraulically powered open die hot forging presses for the forging of steel and non-ferrous metals
EN 14677:2008-Safety of machinery – Secondary steelmaking – Machinery and equipment for treatment of liquid steel
EN 14681:2006+A1:2010-Safety of machinery – Safety requirements for machinery and equipment for production of steel by electric arc furnaces
EN 14710-1:2005+A2:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps without primer – Part 1: Classification, general and safety requirements
EN 14710-2:2005+A2:2008-Fire-fighting pumps – Fire-fighting centrifugal pumps without primer – Part 2: Verification of general and safety requirements
EN 14753:2007-Safety of machinery – Safety requirements for machinery and equipment for continuous casting of steel
EN 14886:2008-Plastics and rubber machines – Bandknife cutting machines for block foams – Safety requirements
EN 14910:2007+A1:2009-Garden equipment – Walk-behind combustion engine powered trimmers – Safety
EN 1492-1:2000+A1:2008-Textile slings – Safety – Part 1: Flat woven webbing slings made of man-made fibres for general purpose use
EN 1492-2:2000+A1:2008-Textile slings – Safety – Part 2: Roundslings made of man-made fibres for general purpose use
EN 1492-4:2004+A1:2008-Textile slings – Safety – Part 4: Lifting slings for general service made from natural and man-made fibre ropes
EN 14930:2007+A1:2009-Agricultural and forestry machinery and gardening equipment – Pedestrian controlled and hand-held machines – Determination of accessibility of hot surfaces
EN 1494:2000+A1:2008-Mobile or movable jacks and associated lifting equipment
EN 1495:1997+A2:2009-Lifting platforms – Mast climbing work platforms
EN 14957:2006+A1:2010-Food processing machinery – Dishwashing machines with conveyor – Safety and hygiene requirements
EN 14958:2006+A1:2009-Food processing machinery – Machinery for grinding and processing flour and semolina – Safety and hygiene requirements
EN 14973:2006+A1:2008-Conveyor belts for use in underground installations – Electrical and flammability safety requirements
EN 14985:2012-Cranes – Slewing jib cranes
EN 15000:2008-Safety of industrial trucks – Self propelled variable reach trucks – Specification, performance and test requirements for longitudinal load moment indicators and longitudinal load moment limiters
EN 15011:2011-Cranes – Bridge and gantry cranes
EN 1501-1:2011-Refuse collection vehicles – General requirements and safety requirements – Part 1: Rear loaded refuse collection vehicles
EN 1501-2:2005+A1:2009-Refuse collection vehicles and associated lifting devices – General requirements and safety requirements – Part 2: Side loaded refuse collection vehicles
EN 1501-3:2008-Refuse collection vehicles and their associated lifting devices – General requirements and safety requirements – Part 3: Front loaded refuse collection vehicles
EN 1501-4:2007-Refuse collection vehicles and their associated lifting devices – General requirements and safety requirements – Part 4: Noise test code for refuse collection vehicles
EN 1501-5:2011-Refuse collection vehicles – General requirements and safety requirements – Part 5: Lifting devices for refuse collection vehicles
EN 15027:2007+A1:2009-Transportable wall saw and wire saw equipment for job site – Safety
EN 15056:2006+A1:2009-Cranes – Requirements for container handling spreaders
EN 15059:2009-Snow grooming equipment – Safety requirements
EN 15061:2007+A1:2008-Safety of machinery – Safety requirements for strip processing line machinery and equipment
EN 15067:2007-Plastics and rubber machines – Film converting machines for bags and sacks – Safety requirements
EN 15093:2008-Safety of Machinery – Safety requirements for hot flat rolling mills
EN 15094:2008-Safety of Machinery – Safety requirements for cold flat rolling mills
EN 15095:2007+A1:2008-Power-operated mobile racking and shelving, carousels and storage lifts – Safety requirements
EN 15162:2008-Machines and plants for mining and tooling of natural stone – Safety requirements for gang saws
EN 15163:2008-Machines and installations for the exploitation and processing of natural stone – Safety – Requirements for diamond wire saws
EN 15164:2008-Machines and plants for mining and tooling of natural stone – Safety – Requirements for chain- and belt-slotting machines
EN 15166:2008-Food processing machinery – Automatic back splitting machines of butchery carcasses – Safety and hygiene requirements
EN 1526:1997+A1:2008-Safety of industrial trucks – Additional requirements for automated functions on trucks
EN 15268:2008-Petrol filling stations – Safety requirements for the construction of submersible pump assemblies
EN 1539:2009-Dryers and ovens, in which flammable substances are released – Safety requirements
EN 1547:2001+A1:2009-Industrial thermoprocessing equipment – Noise test code for industrial thermoprocessing equipment including its ancillary handling equipment
EN 1550:1997+A1:2008-Machine-tools safety – Safety requirements for the design and construction of work holding chucks
EN 15503:2009-Garden equipment – Garden blowers, vacuums and blower/vacuums – Safety
EN 15695-1:2009-Agricultural tractors and self-propelled sprayers – Protection of the operator (driver) against hazardous substances – Part 1: Cab classification, requirements and test procedures
EN 15695-2:2009-Agricultural tractors and self-propelled sprayers – Protection of the operator (driver) against hazardous substances – Part 2: Filters, requirements and test procedures
EN 15700:2011-Safety for conveyor belts for winter sport or leisure use
EN 1570-1:2011-Safety requirements for lifting tables – Part 1: Lifting tables serving up to two fixed landings
EN 15746-2:2010+A1:2011-Railway applications – Track – Road-rail machines and associated equipment – Part 2: General safety requirements
EN 15774:2010-Food processing machinery – Machines for processing fresh and filled pasta (tagliatelle, cannelloni, ravioli, tortellini, orecchiette and gnocchi) – Safety and hygiene requirements
EN 15811:2009-Agricultural machinery – Guards for moving parts of power transmission – Guard opening with tool (ISO/TS 28923:2007 modified)
EN 15895:2011-Cartridge operated hand-held tools – Safety requirements – Fixing and hard marking tools
EN 15949:2012 (new)-Safety of machinery – Safety requirements for bar mills, structural steel mills and wire rod mills
EN 15967:2011-Determination of maximum explosion pressure and the maximum rate of pressure rise of gases and vapours
EN 15997:2011-All terrain vehicles (ATVs – Quads) – Safety requirements and test methods
EN 1612-1:1997+A1:2008-Plastics and rubber machines – Reaction moulding machines – Part 1: Safety requirements for metering and mixing units
EN 1672-2:2005+A1:2009-Food processing machinery – Basic concepts – Part 2: Hygiene requirements
EN 1673:2000+A1:2009-Food processing machinery – Rotary rack ovens – Safety and hygiene requirements
EN 1674:2000+A1:2009-Food processing machinery – Dough and pastry brakes – Safety and hygiene requirements
EN 1677-1:2000+A1:2008-Components for slings – Safety – Part 1: Forged steel components, Grade 8
EN 1677-2:2000+A1:2008-Components for slings – Safety – Part 2: Forged steel lifting hooks with latch, Grade 8
EN 1677-3:2001+A1:2008-Components for slings – Safety – Part 3: Forged steel self-locking hooks – Grade 8
EN 1677-4:2000+A1:2008-Components for slings – Safety – Part 4: Links, Grade 8
EN 1677-5:2001+A1:2008-Components for slings – Safety – Part 5: Forged steel lifting hooks with latch – Grade 4
EN 1677-6:2001+A1:2008-Components for slings – Safety – Part 6: Links – Grade 4
EN 1678:1998+A1:2010-Food processing machinery – Vegetable cutting machines – Safety and hygiene requirements
EN 1679-1:1998+A1:2011-Reciprocating internal combustion engines – Safety – Part 1: Compression ignition engines
EN 1710:2005+A1:2008-Equipment and components intended for use in potentially explosive atmospheres in underground mines
EN 1755:2000+A1:2009-Safety of industrial trucks – Operation in potentially explosive atmospheres – Use in flammable gas, vapour, mist and dust
EN 1756-1:2001+A1:2008-Tail lifts – Platform lifts for mounting on wheeled vehicles – Safety requirements – Part 1: Tail lifts for goods
EN 1756-2:2004+A1:2009-Tail lifts – Platform lifts for mounting on wheeled vehicles – Safety requirements – Part 2: Tail lifts for passengers
EN 1760-1:1997+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 1: General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
EN 1760-2:2001+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 2: General principles for the design and testing of pressure sensitive edges and pressure sensitive bars
EN 1760-3:2004+A1:2009-Safety of machinery – Pressure sensitive protective devices – Part 3: General principles for the design and testing of pressure sensitive bumpers, plates, wires and similar devices
EN 1777:2010-Hydraulic platforms (HPs) for fire fighting and rescue services – Safety requirements and testing
EN 1804-1:2001+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 1: Support units and general requirements
EN 1804-2:2001+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 2: Power set legs and rams
EN 1804-3:2006+A1:2010-Machines for underground mines – Safety requirements for hydraulic powered roof supports – Part 3: Hydraulic control systems
EN 1807:1999+A1:2009-Safety of woodworking machines – Band sawing machines
EN 1808:1999+A1:2010-Safety requirements on Suspended Access Equipment – Design calculations, stability criteria, construction – Tests
EN 1829-1:2010-High pressure water jet machines – Safety requirements – Part 1: Machines
EN 1829-2:2008-High-pressure water jet machines – Safety requirements – Part 2: Hoses, hose lines and connectors
EN 1837:1999+A1:2009-Safety of machinery – Integral lighting of machines
EN 1845:2007-Footwear manufacturing machines – Footwear moulding machines – Safety requirements
EN 1846-2:2009-Firefighting and rescue service vehicles – Part 2: Common requirements – Safety and performance
EN 1846-3:2002+A1:2008-Firefighting and rescue service vehicles – Part 3: Permanently installed equipment – Safety and performance
EN 1853:1999+A1:2009-Agricultural machinery – Trailers with tipping body – Safety
EN 1870-1:2007+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 1: Circular saw benches (with and without sliding table), dimension saws and building site saws
EN 1870-10:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines
EN 1870-11:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 11: Semi-automatic and automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)
EN 1870-12:2003+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 12: Pendulum cross-cut sawing machines
EN 1870-13:2007+A2:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 13: Horizontal beam panel sawing machines
EN 1870-14:2007+A2:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 14: Vertical panel sawing machines
EN 1870-15:2004+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 15: Multiblade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading
EN 1870-16:2005+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 16: Double mitre sawing machines for V-cutting
EN 1870-17:2007+A2:2009-Safety of woodworking machines – Circular sawing machines – Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws)
EN 1870-3:2001+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
EN 1870-4:2012 (new)-Safety of woodworking machines – Circular sawing machines – Part 4: Multiblade rip sawing machines with manual loading and/or unloading
EN 1870-5:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 5: Circular sawbenches/up-cutting cross-cut sawing machines
EN 1870-6:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular saw benches, with manual loading and/or unloading
EN 1870-7:2002+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading
EN 1870-8:2001+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading
EN 1870-9:2000+A1:2009-Safety of woodworking machines – Circular sawing machines – Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading
EN 1889-1:2011-Machines for underground mines – Mobile machines working underground – Safety – Part 1: Rubber tyred vehicles
EN 1889-2:2003+A1:2009-Machines for underground mines – Mobile machines working underground – Safety – Part 2: Rail locomotives
EN 1915-1:2001+A1:2009-Aircraft ground support equipment – General requirements – Part 1: Basic safety requirements
EN 1915-2:2001+A1:2009-Aircraft ground support equipment – General requirements – Part 2: Stability and strength requirements, calculations and test methods
EN 1915-3:2004+A1:2009-Aircraft ground support equipment – General requirements – Part 3: Vibration measurement methods and reduction
EN 1915-4:2004+A1:2009-Aircraft ground support equipment – General requirements – Part 4: Noise measurement methods and reduction
EN 1953:1998+A1:2009-Atomising and spraying equipment for coating materials – Safety requirements
EN 1974:1998+A1:2009-Food processing machinery – Slicing machines – Safety and hygiene requirements
EN 201:2009-Plastics and rubber machines – Injection moulding machines – Safety requirements
EN 267:2009+A1:2011-Automatic forced draught burners for liquid fuels
EN 280:2001+A2:2009-Mobile elevating work platforms – Design calculations – Stability criteria – Construction – Safety – Examinations and tests
EN 289:2004+A1:2008-Plastics and rubber machines – Presses – Safety requirements
EN 30326-1:1994-Mechanical vibration – Laboratory method for evaluating vehicle seat vibration – Part 1: Basic requirements (ISO 10326-1:1992)
EN 349:1993+A1:2008-Safety of machinery – Minimum gaps to avoid crushing of parts of the human body
EN 378-2:2008+A1:2009-Refrigerating systems and heat pumps – Safety and environmental requirements – Part 2: Design, construction, testing, marking and documentation
EN 415-1:2000+A1:2009-Packaging machines safety – Part 1: Terminology and classification of packaging machines and associated equipment
EN 415-3:1999+A1:2009-Safety of packaging machines – Part 3: Form, fill and seal machines
EN 415-5:2006+A1:2009-Safety of packaging machines – Part 5: Wrapping machines
EN 415-6:2006+A1:2009-Safety of packaging machines – Part 6: Pallet wrapping machines
EN 415-7:2006+A1:2008-Safety of packaging machines – Part 7: Group and secondary packaging machines
EN 415-8:2008-Safety of packaging machines – Part 8: Strapping machines
EN 415-9:2009-Safety of packaging machines – Part 9: Noise measurement methods for packaging machines, packaging lines and associated equipment, grade of accuracy 2 and 3
EN 422:2009-Plastics and rubber machines – Blow moulding machines – Safety requirements
EN 453:2000+A1:2009-Food processing machinery – Dough mixers – Safety and hygiene requirements
EN 454:2000+A1:2009-Food processing machinery – Planetary mixers – Safety and hygiene requirements
EN 474-1:2006+A1:2009-Earth-moving machinery – Safety – Part 1: General requirements
EN 474-10:2006+A1:2009-Earth-moving machinery – Safety – Part 10: Requirements for trenchers
EN 474-11:2006+A1:2008-Earth-moving machinery – Safety – Part 11: Requirements for earth and landfill compactors
EN 474-12:2006+A1:2008-Earth-moving machinery – Safety – Part 12: Requirements for cable excavators
EN 474-2:2006+A1:2008-Earth-moving machinery – Safety – Part 2: Requirements for tractor-dozers
EN 474-3:2006+A1:2009-Earth-moving machinery – Safety – Part 3: Requirements for loaders
EN 474-4:2006+A2:2012-Earth-moving machinery – Safety – Part 4: Requirements for backhoe loaders
EN 474-5:2006+A2:2012-Earth-moving machinery – Safety – Part 5: Requirements for hydraulic excavators
EN 474-6:2006+A1:2009-Earth-moving machinery – Safety – Part 6: Requirements for dumpers
EN 474-7:2006+A1:2009-Earth-moving machinery – Safety – Part 7: Requirements for scrapers
EN 474-8:2006+A1:2009-Earth-moving machinery – Safety – Part 8: Requirements for graders
EN 474-9:2006+A1:2009-Earth-moving machinery – Safety – Part 9: Requirements for pipelayers
EN 500-1:2006+A1:2009-Mobile road construction machinery – Safety – Part 1: Common requirements
EN 500-2:2006+A1:2008-Mobile road construction machinery – Safety – Part 2: Specific requirements for road-milling machines
EN 500-3:2006+A1:2008-Mobile road construction machinery – Safety – Part 3: Specific requirements for soil-stabilising machines and recycling machines
EN 500-4:2011-Mobile road construction machinery – Safety – Part 4: Specific requirements for compaction machines
EN 500-6:2006+A1:2008-Mobile road construction machinery – Safety – Part 6: Specific requirements for paver-finishers
EN 50223:2010-Stationary electrostatic application equipment for ignitable flock material – Safety requirements
EN 50348:2010-Stationary electrostatic application equipment for non-ignitable liquid coating material – Safety requirements
EN 50580:2012 (new)-Safety of hand-held electric motor operated tools — Particular requirements for spray guns
EN 528:2008-Rail dependent storage and retrieval equipment – Safety requirements
EN 547-1:1996+A1:2008-Safety of machinery – Human body measurements – Part 1: Principles for determining the dimensions required for openings for whole body access into machinery
EN 547-2:1996+A1:2008-Safety of machinery – Human body measurements – Part 2: Principles for determining the dimensions required for access openings
EN 547-3:1996+A1:2008-Safety of machinery – Human body measurements – Part 3: Anthropometric data
EN 574:1996+A1:2008-Safety of machinery – Two-hand control devices – Functional aspects – Principles for design
EN 60204-1:2006-Safety of machinery – Electrical equipment of machines — Part 1: General requirements
EN 60204-11:2000-Safety of machinery – Electrical equipment of machines — Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV
EN 60204-32:2008-Safety of machinery – Electrical equipment of machines — Part 32: Requirements for hoisting machines
EN 60204-33:2011-Safety of machinery – Electrical equipment of machines — Part 33: Requirements for semiconductor fabrication equipment
EN 60335-1:2012 (new)-Household and similar electrical appliances – Safety — Part 1: General requirements
EN 60335-2-67:2009-Household and similar electrical appliances – Safety — Part 2-67: Particular requirements for floor treatment and floor cleaning machines for commercial use
EN 60335-2-68:2009-Household and similar electrical appliances – Safety — Part 2-68: Particular requirements for spray extraction machines for commercial use
EN 60335-2-69:2009-Household and similar electrical appliances – Safety — Part 2-69: Particular requirements for wet and dry vacuum cleaners, including power brush, for commercial use
EN 60335-2-72:2009-Household and similar electrical appliances – Safety — Part 2-72: Particular requirements for automatic machines for floor treatment for commercial use
EN 60335-2-77:2010-Safety of household and similar appliances — Part 2-77: Particular requirements for pedestrian-controlled walk-behind electrically powered lawn mowers
EN 60335-2-79:2009-Household and similar electrical appliances – Safety — Part 2-79: Particular requirements for high pressure cleaners and steam cleaners
EN 60745-1:2009-Hand-held motor-operated electric tools – Safety — Part 1: General requirements
EN 60745-2-1:2010-Hand-held motor-operated electric tools – Safety — Part 2-1: Particular requirements for drills and impact drills
EN 60745-2-11:2010-Hand-held motor-operated electric tools – Safety — Part 2-11: Particular requirements for reciprocating saws (jig and sabre saws)
EN 60745-2-12:2009-Hand-held motor-operated electric tools – Safety — Part 2-12: Particular requirements for concrete vibrators
EN 60745-2-13:2009-Hand-held motor-operated electric tools – Safety — Part 2-13: Particular requirements for chain saws
EN 60745-2-14:2009-Hand-held motor-operated electric tools – Safety — Part 2-14: Particular requirements for planers
EN 60745-2-15:2009-Hand-held motor-operated electric tools – Safety — Part 2-15: Particular requirements for hedge trimmers
EN 60745-2-16:2010-Hand-held motor-operated electric tools – Safety — Part 2-16: Particular requirements for tackers
EN 60745-2-17:2010-Hand-held motor-operated electric tools – Safety — Part 2-17: Particular requirements for routers and trimmers
EN 60745-2-18:2009-Hand-held motor-operated electric tools – Safety — Part 2-18: Particular requirements for strapping tools
EN 60745-2-19:2009-Hand-held motor-operated electric tools – Safety — Part 2-19: Particular requirements for jointers
EN 60745-2-2:2010-Hand-held motor-operated electric tools – Safety — Part 2-2: Particular requirements for screwdrivers and impact wrenches
EN 60745-2-20:2009-Hand-held motor-operated electric tools – Safety — Part 2-20: Particular requirements for band saws
EN 60745-2-21:2009-Hand-held motor-operated electric tools – Safety — Part 2-21: Particular requirements for drain cleaners
EN 60745-2-22:2011-Hand-held motor-operated electric tools – Safety — Part 2-22: Particular requirements for cut-off machines
EN 60745-2-3:2011-Hand-held motor-operated electric tools – Safety — Part 2-3: Particular requirements for grinders, polishers and disk-type sanders
EN 60745-2-4:2009-Hand-held motor-operated electric tools – Safety — Part 2-4: Particular requirements for sanders and polishers other than disk type
EN 60745-2-5:2010-Hand-held motor-operated electric tools – Safety — Part 2-5: Particular requirements for circular saws
EN 60745-2-6:2010-Hand-held motor-operated electric tools – Safety — Part 2-6: Particular requirements for hammers
EN 60745-2-8:2009-Hand-held motor-operated electric tools – Safety — Part 2-8: Particular requirements for shears and nibblers
EN 60745-2-9:2009-Hand-held motor-operated electric tools – Safety — Part 2-9: Particular requirements for tappers
EN 609-1:1999+A2:2009-Agricultural and forestry machinery – Safety of log splitters – Part 1: Wedge splitters
EN 609-2:1999+A1:2009-Agricultural and forestry machinery – Safety of log splitters – Part 2: Screw splitters
EN 61029-1:2009-Safety of transportable motor-operated electric tools — Part 1: General requirements
EN 61310-1:2008-Safety of machinery – Indication, marking and actuation — Part 1: Requirements for visual, acoustic and tactile signals
EN 61310-2:2008-Safety of machinery – Indication, marking and actuation — Part 2: Requirements for marking
EN 61310-3:2008-Safety of machinery – Indication, marking and actuation — Part 3: Requirements for the location and operation of actuators
EN 614-1:2006+A1:2009-Safety of machinery – Ergonomic design principles – Part 1: Terminology and general principles
EN 614-2:2000+A1:2008-Safety of machinery – Ergonomic design principles – Part 2: Interactions between the design of machinery and work tasks
EN 61496-1:2004-Safety of machinery – Electro-sensitive protective equipment — Part 1: General requirements and tests
EN 617:2001+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for the equipment for the storage of bulk materials in silos, bunkers, bins and hoppers
EN 618:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for equipment for mechanical handling of bulk materials except fixed belt conveyors
EN 619:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for equipment for mechanical handling of unit loads
EN 620:2002+A1:2010-Continuous handling equipment and systems – Safety and EMC requirements for fixed belt conveyors for bulk materials
EN 62061:2005-Safety of machinery – Functional safety of safety-related electrical, electronic and programmable electronic control systems
EN 626-1:1994+A1:2008-Safety of machinery – Reduction of risks to health from hazardous substances emitted by machinery – Part 1: Principles and specifications for machinery manufacturers
EN 626-2:1996+A1:2008-Safety of machinery – Reduction of risk to health from hazardous substances emitted by machinery – Part 2: Methodology leading to verification procedures
EN 676:2003+A2:2008-Automatic forced draught burners for gaseous fuels
EN 690:1994+A1:2009-Agricultural machinery – Manure spreaders – Safety
EN 692:2005+A1:2009-Machine tools – Mechanical presses – Safety
EN 693:2001+A2:2011-Machine tools – Safety – Hydraulic presses
EN 703:2004+A1:2009-Agricultural machinery – Silage loading, mixing and/or chopping and distributing machines – Safety
EN 706:1996+A1:2009-Agricultural machinery – Vine shoot tipping machines – Safety
EN 707:1999+A1:2009-Agricultural machinery – Slurry tankers – Safety
EN 709:1997+A4:2009-Agricultural and forestry machinery – Pedestrian controlled tractors with mounted rotary cultivators, motor hoes, motor hoes with drive wheel(s) – Safety
EN 710:1997+A1:2010-Safety requirements for foundry moulding and coremaking machinery and plant associated equipment
EN 741:2000+A1:2010-Continuous handling equipment and systems – Safety requirements for systems and their components for pneumatic handling of bulk materials
EN 745:1999+A1:2009-Agricultural machinery – Rotary mowers and flail-mowers – Safety
EN 746-1:1997+A1:2009-Industrial thermoprocessing equipment – Part 1: Common safety requirements for industrial thermoprocessing equipment
EN 746-2:2010-Industrial thermoprocessing equipment – Part 2: Safety requirements for combustion and fuel handling systems
EN 746-3:1997+A1:2009-Industrial thermoprocessing equipment – Part 3: Safety requirements for the generation and use of atmosphere gases
EN 786:1996+A2:2009-Garden equipment – Electrically powered walk-behind and hand-held lawn trimmers and lawn edge trimmers – Mechanical safety
EN 791:1995+A1:2009-Drill rigs – Safety
EN 792-12:2000+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 12: Small circular, small oscillating and reciprocating saws
EN 792-13:2000+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 13: Fastener driving tools
EN 792-7:2001+A1:2008-Hand-held non-electric power tools – Safety requirements – Part 7: Grinders
EN 809:1998+A1:2009-Pumps and pump units for liquids – Common safety requirements
EN 81-3:2000+A1:2008-Safety rules for the construction and installation of lifts – Part 3: Electric and hydraulic service lifts
EN 81-31:2010-Safety rules for the construction and installation of lifts – Lifts for the transport of goods only – Part 31: Accessible goods only lifts
EN 81-40:2008-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 40: Stairlifts and inclined lifting platforms intended for persons with impaired mobility
EN 81-41:2010-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 41: Vertical lifting platforms intended for use by persons with impaired mobility
EN 81-43:2009-Safety rules for the construction and installation of lifts – Special lifts for the transport of persons and goods – Part 43: Lifts for cranes
EN 815:1996+A2:2008-Safety of unshielded tunnel boring machines and rodless shaft boring machines for rock – Safety requirements
EN 818-1:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 1: General conditions of acceptance
EN 818-2:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 2: Medium tolerance chain for chain slings – Grade 8
EN 818-3:1999+A1:2008-Short link chain for lifting purposes – Safety – Part 3: Medium tolerance chain for chain slings – Grade 4
EN 818-4:1996+A1:2008-Short link chain for lifting purposes – Safety – Part 4: Chain slings – Grade 8
EN 818-5:1999+A1:2008-Short link chain for lifting purposes – Safety – Part 5: Chain slings – Grade 4
EN 818-6:2000+A1:2008-Short link chain for lifting purposes – Safety – Part 6: Chain slings – Specification for information for use and maintenance to be provided by the manufacturer
EN 818-7:2002+A1:2008-Short link chain for lifting purposes – Safety – Part 7: Fine tolerance hoist chain, Grade T (Types T, DAT and DT)
EN 836:1997+A4:2011-Garden equipment – Powered lawnmowers – Safety
EN 842:1996+A1:2008-Safety of machinery – Visual danger signals – General requirements, design and testing
EN 848-1:2007+A1:2009-Safety of woodworking machines – one side moulding machines with rotating tool – Part 1: Single spindle vertical moulding machines
EN 848-2:2007+A1:2009-Safety of woodworking machines – one side moulding machines with rotating tool – Part 2: Single spindle hand fed/integrated fed routing machines
EN 848-3:2007+A2:2009-Safety of woodworking machines – one side moulding machines with rotating tools – Part 3: Numerically controlled (NC) boring and routing machines
EN 859:2007+A1:2009-Safety of woodworking machines – Hand fed surface planing machines
EN 860:2007+A1:2009-Safety of woodworking machines – one side thickness planing machines
EN 861:2007+A1:2009-Safety of woodworking machines – Surface planing and thicknessing machines
EN 869:2006+A1:2009-Safety of machinery – Safety requirements for pressure metal diecasting units
EN 894-1:1997+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 1: General principles for human interactions with displays and control actuators
EN 894-2:1997+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 2: Displays
EN 894-3:2000+A1:2008-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 3: Control actuators
EN 894-4:2010-Safety of machinery – Ergonomics requirements for the design of displays and control actuators – Part 4: Location and arrangement of displays and control actuators
EN 908:1999+A1:2009-Agricultural and forestry machinery – Reel machines for irrigation – Safety
EN 909:1998+A1:2009-Agricultural and forestry machinery – Centre pivot and moving lateral types irrigation machines – Safety
EN 930:1997+A2:2009-Footwear, leather and imitation leather goods manufacturing machines – Roughing, scouring, polishing and trimming machines – Safety requirements
EN 931:1997+A2:2009-Footwear manufacturing machines – Lasting machines – Safety requirements
EN 940:2009+A1:2012 (new)-Safety of woodworking machines – Combined woodworking machines
EN 953:1997+A1:2009-Safety of machinery – Guards – General requirements for the design and construction of fixed and movable guards
EN 972:1998+A1:2010-Tannery machines – Reciprocating roller machines – Safety requirements
EN 981:1996+A1:2008-Safety of machinery – System of auditory and visual danger and information signals
EN 996:1995+A3:2009-Piling equipment – Safety requirements
EN ISO 10218-1:2011-Robots and robotic devices – Safety requirements for industrial robots – Part 1: Robots (ISO 10218-1:2011)
EN ISO 10218-2:2011-Robots and robotic devices – Safety requirements for industrial robots – Part 2: Robot systems and integration (ISO 10218-2:2011)
EN ISO 10472-1:2008-Safety requirements for industrial laundry machinery – Part 1: Common requirements (ISO 10472-1:1997)
EN ISO 10472-2:2008-Safety requirements for industrial laundry machinery – Part 2: Washing machines and washer-extractors (ISO 10472-2:1997)
EN ISO 10472-3:2008-Safety requirements for industrial laundry machinery – Part 3: Washing tunnel lines including component machines (ISO 10472-3:1997)
EN ISO 10472-4:2008-Safety requirements for industrial laundry machinery – Part 4: Air dryers (ISO 10472-4:1997)
EN ISO 10472-5:2008-Safety requirements for industrial laundry machinery – Part 5: Flatwork ironers, feeders and folders (ISO 10472-5:1997)
EN ISO 10472-6:2008-Safety requirements for industrial laundry machinery – Part 6: Ironing and fusing presses (ISO 10472-6:1997)
EN ISO 10517:2009-Powered hand-held hedge trimmers – Safety (ISO 10517:2009)
EN ISO 10821:2005-Industrial sewing machines – Safety requirements for sewing machines, units and systems (ISO 10821:2005)
EN ISO 11102-1:2009-Reciprocating internal combustion engines – Handle starting equipment – Part 1: Safety requirements and tests (ISO 11102-1:1997)
EN ISO 11102-2:2009-Reciprocating internal combustion engines – Handle starting equipment – Part 2: Method of testing the angle of disengagement (ISO 11102-2:1997)
EN ISO 11111-1:2009-Textile machinery – Safety requirements – Part 1: Common requirements (ISO 11111-1:2009)
EN ISO 11111-2:2005-Textile machinery – Safety requirements – Part 2: Spinning preparatory and spinning machines (ISO 11111-2:2005)
EN ISO 11111-3:2005-Textile machinery – Safety requirements – Part 3: Nonwoven machinery (ISO 11111-3:2005)
EN ISO 11111-4:2005-Textile machinery – Safety requirements – Part 4: Yarn processing, cordage and rope manufacturing machinery (ISO 11111-4:2005)
EN ISO 11111-5:2005-Textile machinery – Safety requirements – Part 5: Preparatory machinery to weaving and knitting (ISO 11111-5:2005)
EN ISO 11111-6:2005-Textile machinery – Safety requirements – Part 6: Fabric manufacturing machinery (ISO 11111-6:2005)
EN ISO 11111-7:2005-Textile machinery – Safety requirements – Part 7: Dyeing and finishing machinery (ISO 11111-7:2005)
EN ISO 11145:2008-Optics and photonics – Lasers and laser-related equipment – Vocabulary and symbols (ISO 11145:2006)
EN ISO 11148-10:2011-Hand-held non-electric power tools – Safety requirements – Part 10: Compression power tools (ISO 11148-10:2011)
EN ISO 11148-11:2011-Hand-held non-electric power tools – Safety requirements – Part 11: Nibblers and shears (ISO 11148-11:2011)
EN ISO 11148-2:2011-Hand-held non-electric power tools – Safety requirements – Part 2: Cutting-off and crimping power tools (ISO/FDIS 11148-2:2011)
EN ISO 11148-3:2010-Hand-held non-electric power tools – Safety requirements – Part 3: Drills and tappers (ISO 11148-3:2010)
EN ISO 11148-4:2010-Hand-held non-electric power tools – Safety requirements – Part 4: Non­rotary percussive power tools (ISO 11148-4:2010)
EN ISO 11148-5:2011-Hand-held non-electric power tools – Safety requirements – Part 5: Rotary percussive drills (ISO 11148-5:2011)
EN ISO 11148-6:2010-Hand-held non-electric power tools – Safety requirements – Part 6: Assembly power tools for threaded fasteners (ISO 11148-6:2010)
EN ISO 11148-8:2011-Hand-held non-electric power tools – Safety requirements – Part 8: Sanders and polishers (ISO 11148-8:2011)
EN ISO 11148-9:2011-Hand-held non-electric power tools – Safety requirements – Part 9: Die grinders (ISO 11148-9:2011)
EN ISO 11161:2007-Safety of machinery – Integrated manufacturing systems – Basic requirements (ISO 11161:2007)
EN ISO 11200:2009-Acoustics – Noise emitted by machinery and equipment – Guidelines for the use of basic standards for the determination of emission sound pressure levels at a work station and at other specified positions (ISO 11200:1995, including Cor 1:1997)
EN ISO 11201:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions in an essentially free field over a reflecting plane with negligible environmental corrections (ISO 11201:2010)
EN ISO 11202:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying approximate environmental corrections (ISO 11202:2010)
EN ISO 11203:2009-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level (ISO 11203:1995)
EN ISO 11204:2010-Acoustics – Noise emitted by machinery and equipment – Determination of emission sound pressure levels at a work station and at other specified positions applying accurate environmental corrections (ISO 11204:2010)
EN ISO 11205:2009-Acoustics – Noise emitted by machinery and equipment – Engineering method for the determination of emission sound pressure levels in situ at the work station and at other specified positions using sound intensity (ISO 11205:2003)
EN ISO 11252:2008-Lasers and laser-related equipment – Laser device – Minimum requirements for documentation (ISO 11252:2004)
EN ISO 11546-1:2009-Acoustics – Determination of sound insulation performances of enclosures – Part 1: Measurements under laboratory conditions (for declaration purposes) (ISO 11546-1:1995)
EN ISO 11546-2:2009-Acoustics – Determination of sound insulation performances of enclosures – Part 2: Measurements in situ (for acceptance and verification purposes) (ISO 11546-2:1995)
EN ISO 11553-1:2008-Safety of machinery – Laser processing machines – Part 1: General safety requirements (ISO 11553-1:2005)
EN ISO 11553-2:2008-Safety of machinery – Laser processing machines – Part 2: Safety requirements for hand-held laser processing devices (ISO 11553-2:2007)
EN ISO 11554:2008-Optics and photonics – Lasers and laser-related equipment – Test methods for laser beam power, energy and temporal characteristics (ISO 11554:2006)
EN ISO 11680-1:2011-Machinery for forestry – Safety requirements and testing for pole-mounted powered pruners – Part 1: Machines fitted with an integral combustion engine (ISO 11680-1:2011)
EN ISO 11680-2:2011-Machinery for forestry – Safety requirements and testing for pole-mounted powered pruners – Part 2: Machines for use with back-pack power source (ISO 11680-2:2011)
EN ISO 11681-1:2011-Machinery for forestry – Portable chain-saw safety requirements and testing – Part 1: Chain-saws for forest service (ISO 11681-1:2011)
EN ISO 11681-2:2011-Machinery for forestry – Portable chain-saw safety requirements and testing – Part 2: Chain-saws for tree service (ISO 11681-2:2011)
EN ISO 11688-1:2009-Acoustics – Recommended practice for the design of low-noise machinery and equipment – Part 1: Planning (ISO/TR 11688-1:1995)
EN ISO 11691:2009-Acoustics – Measurement of insertion loss of ducted silencers without flow – Laboratory survey method (ISO 11691:1995)
EN ISO 11806-1:2011-Agricultural and forestry machinery – Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers – Part 1: Machines fitted with an integral combustion engine (ISO 11806-1:2011)
EN ISO 11806-2:2011-Agricultural and forestry machinery – Safety requirements and testing for portable, hand-held, powered brush-cutters and grass-trimmers – Part 2: Machines for use with back-pack power unit (ISO 11806-2:2011)
EN ISO 11850:2011-Machinery for forestry – General safety requirements (ISO 11850:2011)
EN ISO 11957:2009-Acoustics – Determination of sound insulation performance of cabins – Laboratory and in situ measurements (ISO 11957:1996)
EN ISO 12100:2010-Safety of machinery – General principles for design – Risk assessment and risk reduction (ISO 12100:2010)
EN ISO 13732-1:2008-Ergonomics of the thermal environment – Methods for the assessment of human responses to contact with surfaces – Part 1: Hot surfaces (ISO 13732-1:2006)
EN ISO 13732-3:2008-Ergonomics of the thermal environment – Methods for the assessment of human responses to contact with surfaces – Part 3: Cold surfaces (ISO 13732-3:2005)
EN ISO 13753:2008-Mechanical vibration and shock – Hand-arm vibration – Method for measuring the vibration transmissibility of resilient materials when loaded by the hand-arm system (ISO 13753:1998)
EN ISO 13849-1:2008-Safety of machinery – Safety-related parts of control systems – Part 1: General principles for design (ISO 13849-1:2006)
EN ISO 13849-2:2008-Safety of machinery – Safety-related parts of control systems – Part 2: Validation (ISO 13849-2:2003)
EN ISO 13850:2008-Safety of machinery – Emergency stop – Principles for design (ISO 13850:2006)
EN ISO 13855:2010-Safety of machinery – Positioning of safeguards with respect to the approach speeds of parts of the human body (ISO 13855:2010)
EN ISO 13857:2008-Safety of machinery – Safety distances to prevent hazard zones being reached by upper and lower limbs (ISO 13857:2008)
EN ISO 14122-1:2001-Safety of machinery – Permanent means of access to machinery – Part 1: Choice of fixed means of access between two levels (ISO 14122-1:2001)
EN ISO 14122-2:2001-Safety of machinery – Permanent means of access to machinery – Part 2: Working platforms and walkways (ISO 14122-2:2001)
EN ISO 14122-3:2001-Safety of machinery – Permanent means of access to machinery – Part 3: Stairs, stepladders and guard-rails (ISO 14122-3:2001)
EN ISO 14122-4:2004-Safety of machinery – Permanent means of access to machinery – Part 4: Fixed ladders (ISO 14122-4:2004)
EN ISO 14159:2008-Safety of machinery – Hygiene requirements for the design of machinery (ISO 14159:2002)
EN ISO 14314:2009-Reciprocal internal combustion engines – Recoil starting equipment – General safety requirements (ISO 14314:2004)
EN ISO 14738:2008-Safety of machinery – Anthropometric requirements for the design of workstations at machinery (ISO 14738:2002, including Cor 1:2003 and Cor 2:2005)
EN ISO 14982:2009-Agricultural and forestry machinery – Electromagnetic compatibility – Test methods and acceptance criteria (ISO 14982:1998)
EN ISO 15536-1:2008-Ergonomics – Computer manikins and body templates – Part 1: General requirements (ISO 15536-1:2005)
EN ISO 15744:2008-Hand-held non-electric power tools – Noise measurement code – Engineering method (grade 2) (ISO 15744:2002)
EN ISO 19432:2008-Building construction machinery and equipment – Portable, hand-held, internal combustion engine driven cut-off machines – Safety requirements and testing (ISO 19432:2006)
EN ISO 20361:2009-Liquid pumps and pump units – Noise test code – Grades 2 and 3 of accuracy (ISO 20361:2007)
EN ISO 20643:2008-Mechanical vibration – Hand-held and hand-guided machinery – Principles for evaluation of vibration emission (ISO 20643:2005)
EN ISO 2151:2008-Acoustics – Noise test code for compressors and vacuum pumps – Engineering method (Grade 2) (ISO 2151:2004)
EN ISO 22867:2011-Forestry and gardening machinery – Vibration test code for portable hand-held machines with internal combustion engine – Vibration at the handles (ISO 22867:2011)
EN ISO 22868:2011-Forestry and gardening machinery – Noise test code for portable hand-held machines with internal combustion engine – Engineering method (Grade 2 accuracy) (ISO 22868:2011)
EN ISO 23125:2010-Machine tools – Safety – Turning machines (ISO 23125:2010)
EN ISO 28139:2009-Agricultural and forestry machinery – Knapsack combustion-engine-driven mistblowers – Safety requirements (ISO 28139:2009)
EN ISO 2860:2008-Earth-moving machinery – Minimum access dimensions (ISO 2860:1992)
EN ISO 2867:2011-Earth-moving machinery – Access systems (ISO 2867:2011)
EN ISO 28927-1:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 1: Angle and vertical grinders (ISO 28927-1:2009)
EN ISO 28927-10:2011-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 10: Percussive drills, hammers and breakers (ISO 28927-10:2011)
EN ISO 28927-11:2011-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 11: Stone hammers (ISO 28927-11:2011)
EN ISO 28927-2:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 2: Wrenches, nutrunners and screwdrivers (ISO 28927-2:2009)
EN ISO 28927-3:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 3: Polishers and rotary, orbital and random orbital sanders (ISO 28927-3:2009)
EN ISO 28927-4:2010-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 4: Straight grinders (ISO 28927-4:2010)
EN ISO 28927-5:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 5: Drills and impact drills (ISO 28927-5:2009)
EN ISO 28927-6:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 6: Rammers (ISO 28927-6:2009)
EN ISO 28927-7:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 7: Nibblers and shears (ISO 28927-7:2009)
EN ISO 28927-8:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 8: Saws, polishing and filing machines with reciprocating action and saws with oscillating or rotating action (ISO 28927-8:2009)
EN ISO 28927-9:2009-Hand-held portable power tools – Test methods for evaluation of vibration emission – Part 9: Scaling hammers and needle scalers (ISO 28927-9:2009)
EN ISO 3164:2008-Earth-moving machinery – Laboratory evaluations of protective structures – Specifications for deflection-limiting volume (ISO 3164:1995)
EN ISO 3266:2010-Forged steel eyebolts grade 4 for general lifting purposes (ISO 3266:2010)
EN ISO 3411:2007-Earth-moving machinery – Physical dimensions of operators and minimum operator space envelope (ISO 3411:2007)
EN ISO 3449:2008-Earth-moving machinery – Falling-object protective structures – Laboratory tests and performance requirements (ISO 3449:2005)
EN ISO 3450:2011-Earth-moving machinery – Wheeled or high-speed rubber-tracked machines – Performance requirements and test procedures for brake systems (ISO 3450:2011)
EN ISO 3457:2008-Earth-moving machinery – Guards – Definitions and requirements (ISO 3457:2003)
EN ISO 3471:2008-Earth-moving machinery – Roll-over protective structures – Laboratory tests and performance requirements (ISO 3471:2008)
EN ISO 3741:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for reverberation test rooms (ISO 3741:2010)
EN ISO 3743-1:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for small movable sources in reverberant fields – Part 1: Comparison method for a hard-walled test room (ISO 3743-1:2010)
EN ISO 3743-2:2009-Acoustics – Determination of sound power levels of noise sources using sound pressure – Engineering methods for small, movable sources in reverberant fields – Part 2: Methods for special reverberation test rooms (ISO 3743-2:1994)
EN ISO 3744:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering methods for an essentially free field over a reflecting plane (ISO 3744:2010)
EN ISO 3745:2012 (new)-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Precision methods for anechoic rooms and hemi-anechoic rooms (ISO 3745:2012)
EN ISO 3746:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Survey method using an enveloping measurement surface over a reflecting plane (ISO 3746:2010)
EN ISO 3747:2010-Acoustics – Determination of sound power levels and sound energy levels of noise sources using sound pressure – Engineering/survey methods for use in situ in a reverberant environment (ISO 3747:2010)
EN ISO 4254-1:2009-Agricultural machinery – Safety – Part 1: General requirements (ISO 4254-1:2008)
EN ISO 4254-10:2009-Agricultural machinery – Safety – Part 10: Rotary tedders and rakes (ISO 4254-10:2009)
EN ISO 4254-11:2010-Agricultural machinery – Safety – Part 11: Pick-up balers (ISO 4254-11:2010)
EN ISO 4254-5:2009-Agricultural machinery – Safety – Part 5: Power-driven soil-working machines (ISO 4254-5:2008)
EN ISO 4254-6:2009-Agricultural machinery – Safety – Part 6: Sprayers and liquid fertilizer distributors (ISO 4254-6:2009)
EN ISO 4254-7:2009-Agricultural machinery – Safety – Part 7: Combine harvesters, forage harvesters and cotton harvesters (ISO 4254-7:2008)
EN ISO 4413:2010-Hydraulic fluid power – General rules and safety requirements for systems and their components (ISO 4413:2010)
EN ISO 4414:2010-Pneumatic fluid power – General rules and safety requirements for systems and their components (ISO 4414:2010)
EN ISO 4871:2009-Acoustics – Declaration and verification of noise emission values of machinery and equipment (ISO 4871:1996)
EN ISO 5136:2009-Acoustics – Determination of sound power radiated into a duct by fans and other air-moving devices – In-duct method (ISO 5136:2003)
EN ISO 5674:2009-Tractors and machinery for agriculture and forestry – Guards for power take-off (PTO) drive-shafts – Strength and wear tests and acceptance criteria (ISO 5674:2004, corrected version 2005-07-01)
EN ISO 6682:2008-Earth-moving machinery – Zones of comfort and reach for controls (ISO 6682:1986, including Amd 1:1989)
EN ISO 6683:2008-Earth-moving machinery – Seat belts and seat belt anchorages – Performance requirements and tests (ISO 6683:2005)
EN ISO 7096:2008-Earth-moving machinery – Laboratory evaluation of operator seat vibration (ISO 7096:2000)
EN ISO 7235:2009-Acoustics – Laboratory measurement procedures for ducted silencers and air-terminal units – Insertion loss, flow noise and total pressure loss (ISO 7235:2003)
EN ISO 7731:2008-Ergonomics – Danger signals for public and work areas – Auditory danger signals (ISO 7731:2003)
EN ISO 8230-1:2008-Safety requirements for dry-cleaning machines – Part 1: Common safety requirements (ISO 8230-1:2008)
EN ISO 8230-2:2008-Safety requirements for dry-cleaning machines – Part 2: Machines using perchloroethylene (ISO 8230-2:2008)
EN ISO 8230-3:2008-Safety requirements for dry-cleaning machines – Part 3: Machines using combustible solvents (ISO 8230-3:2008)
EN ISO 9614-1:2009-Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 1: Measurement at discrete points (ISO 9614-1:1993)
EN ISO 9614-3:2009-Acoustics – Determination of sound power levels of noise sources using sound intensity – Part 3: Precision method for measurement by scanning (ISO 9614-3:2002)
EN ISO 9902-1:2001-Textile machinery – Noise test code – Part 1: Common requirements (ISO 9902-1:2001)
EN ISO 9902-2:2001-Textile machinery – Noise test code – Part 2: Spinning preparatory and spinning machinery (ISO 9902-2:2001)
EN ISO 9902-3:2001-Textile machinery – Noise test code – Part 3: Nonwoven machinery (ISO 9902-3:2001)
EN ISO 9902-4:2001-Textile machinery – Noise test code – Part 4: Yarn processing, cordage and rope manufacturing machinery (ISO 9902-4:2001)
EN ISO 9902-5:2001-Textile machinery – Noise test code – Part 5: Weaving and knitting preparatory machinery (ISO 9902-5:2001)
EN ISO 9902-6:2001-Textile machinery – Noise test code – Part 6: Fabric manufacturing machinery (ISO 9902-6:2001)
EN ISO 9902-7:2001-Textile machinery – Noise test code – Part 7: Dyeing and finishing machinery (ISO 9902-7:2001)


Up